# Error display on reset - Send Flag Timed Out Busy

**URL:** <https://forums.sifive.com/t/error-display-on-reset-send-flag-timed-out-busy/3662>\
**Category:** HiFive1 Rev B\
**Created:** [May 18, 2020, 3:44pm UTC](https://forums.sifive.com/t/error-display-on-reset-send-flag-timed-out-busy/3662 "2020-05-18T15:44:37Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![abehnke](https://avatars.discourse-cdn.com/v4/letter/a/e95f7d/32.png) [@abehnke](https://forums.sifive.com/u/abehnke)\
**Post date:** [May 18, 2020, 3:44pm UTC](https://forums.sifive.com/t/error-display-on-reset-send-flag-timed-out-busy/3662/1 "2020-05-18T15:44:37Z")

</div>

Whenever I reset a program (with the button), I get the following Terminal output on COM7:

Bench Clock Reset Complete

ATE0–\>Send Flag Timed Out Busy. Giving Up.  
Send Flag error: #0 #0 #0 #0 AT+BLEINIT=0–\>Send Flag Timed Out Busy. Giving Up.  
Send Flag error: #0 #0 #0 #0 AT+CWMODE=0–\>Send Flag Timed Out Busy. Giving Up.  
Send Flag error: #0 #0 #0 #0

Followed by the expected display from the particular example program. I tried using a separate power supply of 7 to 10 volts on the power input connector but that made no difference. Could my ESP32-SOLO part be broken? I get no output on COM6. The fe310-g002 works and the JLINK debugger works.

environment:  
win 7 64  
HiFive1 Rev B board  
SiFive Eclipse IDE for C/C++ Development Version: 4.12.0.2019-08-2

---

<div class="post-metadata">

**Author:** ![abehnke](https://avatars.discourse-cdn.com/v4/letter/a/e95f7d/32.png) [@abehnke](https://forums.sifive.com/u/abehnke)\
**Post date:** [July 18, 2020, 3:58pm UTC](https://forums.sifive.com/t/error-display-on-reset-send-flag-timed-out-busy/3662/2 "2020-07-18T15:58:50Z")

</div>

Problem solved. When I use putty to connect to COM6 (the ESP32-SOLO thru MK22FN), I need to enable flow control RTS/CTS. I found that pin 3 - EN of the ESP32-SOLO was at 0.3 volts - should be hi. The FE310 attempts to enable ESP32-SOLO but the MK22FN disagrees. MK22FN pin 44 -\> DBG\_UART1\_RTS connects to WF\_RESET\_R.

FE310 running hifive1revb\_wifi from kjarvel

My setup appears sensitive to the order of power on, reset, connecting putty etc. This works sometimes:

1. Plug in USB
2. Open 1st putty on COM7
3. Push RESET

output is:  
Bench Clock Reset Complete  
ATE0–\>ATE0  
OK  
AT+BLEINIT=0–\>OK  
AT+CWMODE=0–\>OK

1. Open 2nd putty on COM6
2. Press RESET again
3. ESP/wifi boot up displays on COM6

Note: once I used putty on COM6 with RTS - something now remembers that setting even without connecting putty to COM6.
